2018-08-03 The installation precision of the chemical fiber spinning metering pump

The chemical fiber spinning metering pump is a kind of gear pump, which is mainly used in the field of chemical fiber spinning. The BART melt pump manufacturer provides ZB-U series of chemical fiber spinning metering pump, the working temperature is less than 350 degrees C, and the maximum pressure difference is 40MPa. The chemical fiber spinning metering pump is the heart component of the spinning machine, plays the role of quantitative, constant pressure, and uniform delivery of spinning material (Bart provides the advantages of pressure, wear resistance, long service life and so on). On the

2018-07-25 The advantages and application scope of the melt pump

The ZB-G series melt pump is mainly used for extrusion process of rubber and plastics. It is used in conjunction with extruder and installed at the outlet of extruder. ZB-K series melt pump has the best ability to deal with high viscosity materials, mainly used for polymer and prepolymer transportation. ZB-T series of melt pumps are used in general chemical processes. Advantages: the polymer melt pump ZB series adopts unique volume design, which can provide stable and accurate polymer metering in the condition of constant pressure, temperature and viscosity. Due to the pressure of the ZB melt

2018-07-17 Silicone rubber compound gear pump

n the filtration of silicone rubber compound, the advantage of using a gear pump is significantly larger than that of other rubber compounds, such as EPDM. This is because silicone rubber compounds have very low viscosity, so the pressure increase has a greater impact on the output of the single screw extruder. For example, the test results show that for a specific organosilicon compound, if the pressure is increased from 10 bar to 40 bar, the output of single cycle single screw will be reduced by 50%. Due to the low viscosity of silicone rubber, even under relatively low pressure growth, ther

2018-06-27 The working temperature of the melt pump

All the gears and mating surfaces of the melt pump produced by our company are finely grinded, and the clearance of assembly is strictly controlled to achieve accurate flow. The gear and the pump body use the chromium nickel alloy steel and the high temperature tool steel material according to the ZB-B series of different working conditions; the ZB-H series adopts the imported CPM tool steel or the titanium tantalum alloy material, which is quenched as a whole, the hardness is HRC62-68, and the wear resistance is good. 1. ZB-B series melt pump : working temperature: less than 400 C (750), clea

2018-06-15 How to adjust the sealing system of the melt pump

The new melt pump is 24 h before driving for the first time, and the clearance of the packing gland is generally 9 mm (the factory has been set at the factory); the filler is added to the silicone oil bubble and the silicone oil leakage to the pump is normal. Before the preparation of the grain, the pressure control screw is used to guarantee the full discharge of the waste waste and the speed of the pressure control screw melt pump is controlled at 25 r/min. The pressure control screw rotates inward, pressure to show 0.3-0.5 MPa. When the melt pump reaches the normal production speed, seal ca

2018-06-07 Assembly of melt pump

1. before the assembly of the melt pump , a tank of lubricant, pump body, front and back cover plate, active and driven gear, sealing components and sealing gland should be assembled before lubrication. When assembling, please install the parts one by one in strict accordance with the disassembly sequence of each component, so that all parts are correctly reset. 2. before installing the bolts, melt the threaded parts with high temperature grease and tighten the bolts of the front and rear covers in diagonal way. Always remain free to rotate. If there is any stuck phenomenon, the melt pump must

2018-05-29 PVC resin production line dedicated melt pump

1.This PVC pipe extrusion melt pump is widely used for producing PVC water supply pipe,drainage pipe and high voltage cable protection pipe. 2.With CPVC pipe mold,it could also produce CPVC pipe. 3.It is consists of SJSZ series melt pump extruder ,mold,vacuum tank,spraying cooling tank,haul-off,cutting machine,stacker,and can produce PVC pipe from mixed powder directly. 4.The production line uses special designed screw and mold,which makes it easy forming,even plasticization,high capacity,stable running and easy operation. Batte Melt Pump Zhengzhou Co.,Ltd is a professional melt pumps manufact

2018-05-21 Effect of rubber extrusion melt pump on rubber extrusion line

With the continuous and stable development of rubber industry, the demand for rubber products is increasing. In particular, in recent years, family cars have been flying into the common peoples house, which has led to the great development of EPDM ethylene propylene rubber, NBR, SBR rubber materials and products, including sealing strips, resin modification, wires, cables, tubes and plastic runways, etc. Because of the particularity of rubber processing technology, the melt pump specially used for rubber is of great significance in the production line. The temperature control principle of gear

2018-05-02 Method of improving the service life of high temperature pump

1, because of the high temperature melt pump body running at high temperature, so the cold installation of piping should be equipped with hinge support, to prevent pipe displacement after heating. 2, the coupling must be heated up after the pump body is heated, so as to avoid additional torque when running. 3. When the high temperature melt pump starts, no pressure can be speeded up when the outlet pressure is not formed, so as to prevent premature damage of the shaft or bearing. 4. The temperature of the heat medium jacket of the high temperature melt pump body can be slightly lower than the

2018-04-23 Optimum application field of melt gear pump

As a manufacturing enterprise of large melt gear pump in China, batte has many years of experience in equipment development and production. It provides the best melt pump equipment for many plastics extrusion users in China, improves the efficiency of plastic extrusion line and creates more productive benefits for the plastic extrusion users. Below Lantai analyzes and explains the best application scope of melt gear pump. It is suitable for the extruder with poor pressure building, such as the co rotating twin screw extruder, multistage exhaust extruder, and so on. The application of the melt